Jual Lantai Kayu – Vinyl Floor – Parket Indonesia

Home > Installation
  • installation

Install Meforze Laminate Flooring

TOOLS AND MATERIAL

  • Broom
  • Carpenter’s square
  • Chalk line
  • Crow or Pull bar
  • Electric and/or handsaw (Jigsaw)
  • Hammer
  • Spacers
  • Tape Measure
  • Tapping Block
  • Utility knife
  • Utility Towels

INSTALL THE UNDERLAYER

  • Lay out the underlayer above the subfloor.
  • Tape at all seams to hold sheet together.
  • Trim all edges at the wall level using a utility knife.

INSTALL THE FIRST ROW

  • Along the longest wall, measure out your expansion spacing usually ¼”) in at least two places and snap a chalk line.
  • Lay out the laminate with the groove toward the wall but do not lock together yet. Add spacers between the flooring and the wall. Make sure this first row is completely straight. Scribe fit (if necessary) so that the laminate matches the contours of the wall.
  • Once satisfied with the fit, click and lock the first row of laminate together. There should be no space between locked boards.
  • At the end of the wall, measure, cut and lock the last laminate plank in place. Add a spacer at the end of the first row.
  • Evaluate this first row to ensure it is straight and level. Adjust where needed.

INSTALL THE MAIN PART OF THE FLOOR

  • Use a partial board (approx 8”-10” in length) to start the second row.
  • Click and lock laminate boards together as you did with the first row.
  • Work your way across the floor until you reach the last row.

INSTALL THE LAST ROW

  • Measure out your expansion spacing (usually ¼”) in at least two places and snap a chalk line.
  • Lay out the last row of laminate with the tongue or cut part toward the wall. Scribe fit (if necessary) so that the laminate matches any contours in the wall. Make sure this last row is completely straight.
  • Once satisfied with the fit, click and lock each plank in the last row together with the rest of the floor.
  • Evaluate the last row to ensure it is straight and level. Adjust where needed.
  • Once you lock the board into place, you can remove all spacers and begin using your MEFORZE Laminate Flooring.

Install Meforze Vinyl Floor

TOOLS AND MATERIAL

  • Chalk line
  • Full Spread Adhesive
  • Carpenter’s Square
  • Felt-tipped pen and/or pencil
  • Measuring tape and/or ruler
  • Notched trowel
  • Utility knife
  • Vinyl cutter, shears or snips

INSTALL VINYL FLOOR

Vinyl Plank : Size 152,4 x 914,4 mm (6″x36″)

Vinyl Plank step 1     Vinyl Plank step 2     Vinyl Plank step 3

Vinyl Tile : Size 457,2 x 457,2 (18″x18″)
Vinyl Tile step 1     Vinyl Tile step 2     Vinyl Tile step 3

  • Snap a chalk line between the center points of each opposite wall to divide the room into four equal quadrants.
  • Layout a row of loose vinyl in all directions at the center inter section point. Evaluate the fit. If there are small cuts (leens than 1/2″) along walls, move the starting point down by 1/2 a vinyl width and re-snap your chalk lines. If desired, snap chalks lines to divide the larger quadrants into smaller (approx 2′ x 3′) sections.
  • Begin securing vinyl floor at the center intersection point in one quadrant and work your way towards the walls.
  • Sweep and vacum the floor so it is completely clean.
  • Beginning at the center point, install the first vinyl floor so it aligns with the two main chalk lines in the center of the room. Apply the adhesive to the subfloor as directed by the manufacturer.
  • Place another vinyl floor next to the first one in one direction of the room then along the other direction. Vinyl floor should be snug but not overlapping.
  • When you reach a wall, scribe fit the vinyl floor. Place a full vinyl floor directly on top of the one you just installed near the wall. Place a second vinyl floor on top of the other two butted up against the wall (Leave expansion spacing, if needed). Use a pencil to mark the inner edge of the top vinyl floor one the middle one. Remove the middle one and cut along the line. The cut vinyl floor should now be the exact width you need for your installation area.
  • Continue installing vinyl floor in each section and quadrant until the floor is completed.
  • Roll the newly installed vinyl floor with a roller.
  • Let the newly installed vinyl floor cure between 24-72 hours. During this time, do not move anything back into the room and keep traffic to a minimum.